If you’ve ever had a toilet that won’t flush all the way, you know how frustrating it can be. Not only is it unpleasant to leave waste in the toilet bowl, but it can also lead to bad smells and a messy bathroom.
There are a few reasons why a toilet might not flush all the way. This includes:
You have set your toilet tank’s water level too low
Your toilet tank holds a specific amount of water for a reason – and that reason is so your toilet can flush properly. When you have less water in the tank, it means that there is less force behind the flush, and that can lead to all sorts of problems. Your toilet may not be flushed completely, leaving behind waste and trapped odour.
Additionally, a low water level can also lead to frequent clogs, as there isn’t enough water to properly move solid waste through the pipes.
If you’ve determined that your water level is too low, the solution is easy – simply adjust your float. By raising the float, you’ll increase the amount of water in the tank, and that will help ensure a stronger flush and fewer clogs.
You have issues with your flapper
The flapper is the rubber seal that covers the hole at the bottom of the tank and allows water to flow through when you flush the toilet.
Over time, the flapper can become cracked or warped, preventing it from forming a tight seal. As a result, water will slowly leak out of the tank, causing the toilet to lose its power.
To fix this problem, simply replace the flapper with a new one. Be sure to measure the size of your flapper before heading to the store, as there are many different sizes available. With a new flapper in place, your toilet should be able to flush normally again.
A blockage in the inlet holes
Check to see if the inlet holes at the bottom of the bowl are blocked. These holes allow water to enter the bowl, and if they’re blocked, it can prevent the bowl from draining properly. If the inlet holes are clear, try using a plunger to unclog the drain.
If that doesn’t work, you may need to remove the toilet tank lid and check to see if the water level is too low. If it is, adjust the float until the water level is high enough. You should also check for any leaks in the tank and make sure that all of the connections are tight.
Issues with the design of your drain pipe
If your toilet won’t flush all the way, it’s usually due to a problem with the drain pipe. The most common issue is that the pipe is too small in diameter, which doesn’t allow enough water to flow through and rinse everything away.
Another possibility is that the pipe is blocked by a clog or an object that’s preventing water from flowing freely.
In either case, you’ll need to call a plumber to fix the problem. In the meantime, you can try using a plunger to unblock the drain or straighten out the kink in the pipe.
If that doesn’t work, you can try pouring a bucket of water into the toilet bowl to flush away any remaining waste. With a little troubleshooting, you should be able to get your toilet flushing properly in no time.
Your system is clogged
When your toilet won’t flush all the way, it’s usually due to a clog in the toilet, flange, or drain. The first thing you should do is check the toilet bowl for any foreign objects that may be causing the blockage.
If you don’t see anything, try flushing the toilet again. If the water level doesn’t go down, then you know you have a clog.
The next thing you should do is reach for a plunger. Put the plunger over the hole at the bottom of the bowl and push and pull the plunger up and down. Be sure to use enough force to push the clog through.
If that doesn’t work, you may need to use a wire hanger or plumbers’ snake to dislodge the clog. Finally, if all else fails, you can always call a plumber to take care of the problem for you.
Contact Expert Plumbing and Solar Services Bathurst today
Is your toilet running non-stop, or does it seem to take forever to fill up after flushing? These are both common signs that you have a leak in your toilet tank.
While this may not seem like a big deal, a leaky toilet can actually waste a lot of water and increase your water bill. In addition, if the leak is not fixed, it can cause significant damage to your bathroom floor and fixtures.
If you are experiencing any type of issue with your toilet, it is important to call a plumbing expert right away. The experts at Expert Plumbing and Solar Services Bathurst have years of experience dealing with all types of toilet issues. We will quickly diagnose the problem and provide you with an effective solution.
So don’t wait, call us today at (02) 6332 4992.
